Introduction[]
One episode. shown at 0:30 in this video. I calced this before. However, someone had issues with it, this will update to handle their issues.
Pixel measurement[]
Earl is 428 pixels and 187.96 centimeters. (He is 6 foot 2 inches)
Earls head is 68 pixels and 29.86280373831776 centimeters
Earl head is 102 pixels and 29.86280373831776 centimeters
Length Wall 822 pixels and 240.6590654205608 centimeters
Height wall 423 pixels 123.8428037383178 centimeters
Width wall is 3.334 centimeters assuming the average.
Take that to a cubic centimeter calculator and
99366.180618023 CC
This was definitely Very high V Frag to Pulverize. So. We shall do both ends. From what I found on this calc. V Frag is 18.34. And Pulverize is between 32.51 and 61.36
So. For the final result
V Frag
99366.180618023 * 18.34 = 1,822,375.752534542 Joules. Wall level
Pulverize low end
99366.180618023 * 31.51 = 3,131,028.351273905 Joules. Wall level
Pulverize high end
99366.180618023 * 61.36 = 6,097,108.842721892 Joules. Wall level
Hollowness[]
Now here was the problem they had raised up. They said the wall was mostly hollow. IMO. They are wrong. These frames here honestly tell me the wall isn’t really hollow, it’s only a fake wall so he could actually be smashed through it. (Much like break away glass, it’s for the actors). These frames showing it isn’t really hollow inside as well. But in case hollowness needs to be considered. I’ll add it. Though my arguments are under the pictures
Here it shows from this angle that it’s not really hollow at all. It is one solid piece through it when you look at the holes edges. It’s not a wall with a gap in between rooms. This picture and angle shows there is like no room or reason it would. It’s too small and pointless
Here it shows no room for hollowness and just is a thin wall, as shown he can place his hands around the ends. There would be no visible room for any real hollowness, especially since the tiny piece we see in the picture before is within the width of the wall from looks.
But anyways. With these frames. Even if we assume hollowness. The walls should not be very hollow at all. As I showed above, there was hardly any room to be hollow. It wouldn’t make sense for it to be hollow very hollow at all.
I’ll account 2 ends. 20 percent hollowness. And 50 percent.
20 percent end
V Frag
99366.180618023 * 18.34 = 1,822,375.752534542 Joules. Accounting hollowness
1,457,900.60203 Joules. Wall level
Pulverize low end
99366.180618023 * 31.51 = 3,131,028.351273905 Joules. Accounting hollowness
2,504,822.68102 Joules. Wall level
Pulverize high end
99366.180618023 * 61.36 = 6,097,108.842721892 Joules. Accounting hollowness
4,877,687.07418 Joules. Wall level
50 percent end
V Frag
99366.180618023 * 18.34 = 1,822,375.752534542 Joules. Accounting hollowness
911,187.876267271 Joules. Wall level
Pulverize low end
99366.180618023 * 31.51 = 3,131,028.351273905 Joules. Accounting hollowness
1,565,514.175636952 Joules. Wall level
Pulverize high end
99366.180618023 * 61.36 = 6,097,108.842721892 Joules. Accounting hollowness
3,048,554.421360946 Joules. Wall level
Final Results[]
Non Hollow V Frag end = 1,822,375.752534542 Joules Wall level
Non Hollow Pulverize Lower End = 3,131,028.351273905 Joules Wall level
Non Hollow Pulverize Higher End = 6,097,108.842721892 Joules Wall level
20 percent V Frag End = 1,457,900.60203 Joules. Wall level
20 percent Pulverize Lower End = 2,504,822.68102 Joules. Wall level
20 percent Pulverize Higher End = 4,877,687.07418 Joules. Wall level
50 percent V Frag End = 911,187.876267271 Joules. Wall level
50 percent Pulverize Lower End = 1,565,514.175636952 Joules. Wall level
50 percent Pulverize Higher End = 3,048,554.421360946 Joules. Wall level
My preference is against a Hollow end at all. As my reasons above explain that this wall has no room to be hollow, and makes 0 sense why it would be hollow. This looks more like a standard wall with no in between cause it’s a motel. So I’m an fully against hollow, but here it is with both ends just in case.
Note: In accordance with Rule Violations Report Thread 75, the calculations of this user are not to be used. Wokistan (talk) 14:48, September 3, 2020 (UTC)